Rajasthan receives limited rainfall, and groundwater levels in many areas, including Jaipur, have fallen sharply over the years. Yet a large share of the rain that falls on rooftops and paved areas simply runs into drains. Rainwater harvesting captures this water for storage or groundwater recharge. For many new buildings, local building rules also require rainwater harvesting structures, so planning them properly from the design stage is both responsible and practical.
1. Why buildings need rainwater harvesting
- Recharges groundwater and supports borewell yields over time.
- Reduces waterlogging and load on city drains during heavy rain.
- Provides stored water for gardening, flushing or cleaning where permitted.
- Helps meet building approval conditions in many urban areas.
Rules on mandatory rainwater harvesting depend on plot size and local authority byelaws; check the conditions in your building plan approval. Our building plan approval guide explains the approval process.
2. Main components of a system
- Catchment: the roof or paved area that collects rain.
- Conveyance: gutters and down-pipes that carry water.
- First-flush device: diverts the dirtiest first rain away.
- Filter: sand, gravel and charcoal layers or a ready-made filter unit.
- Storage tank and/or recharge structure.

3. Recharge pits, trenches and wells
Where storage is not needed, water can be directed into recharge structures. Recharge pits are filled with layers of boulders, gravel and sand; recharge trenches suit long, narrow plots; and recharge wells or shafts reach deeper permeable layers. Existing borewells can sometimes be used for recharge, but only with proper filtration to avoid contaminating the aquifer. Site soil and water table conditions guide the choice.
4. Storage tanks
Collected rainwater can be stored in underground or overground tanks for non-potable uses. Tanks must be covered, have overflow arrangements and be protected from mosquito breeding. Drinking use requires proper treatment and testing, and should be designed only with expert advice. Waterproofing of underground tanks follows the same principles as our waterproofing guide.
5. Sizing the system
The volume of water available depends on roof area, rainfall and a runoff coefficient that reflects the surface type. An engineer uses these figures to size pipes, filters, tanks and recharge pits so that overflow during heavy spells is safely handled. Oversized tanks waste money; undersized pits overflow. Good design balances both.
6. Industrial and commercial sites
Factories, warehouses and campuses have large roofs and paved yards, so the potential is significant. Separate clean roof water from yard runoff that may carry oil or chemicals, which needs oil-water separators before any recharge. The ATTPL Group guide to industrial shed and warehouse planning shows how drainage fits into site layouts. Rooftops can also host solar panels from ATTPL Solar alongside gutters and down-pipes when planned together.
7. Common mistakes in building projects
- Connecting kitchen or toilet waste water to recharge pits, which pollutes groundwater.
- Building pits without filter layers, so they clog within a season.
- Placing recharge pits too close to foundations or basements.
- Ignoring overflow arrangements, causing waterlogging during heavy rain.
- Treating the system as a formality for approval and never maintaining it.
Most of these mistakes are avoided when the system is designed by an engineer and built under supervision, just like any other part of the building.
8. Working with the design team
Ask your architect and plumbing consultant to show the rainwater system on drawings: roof slopes, down-pipe locations, filter chambers, tanks, pits and overflow routes. Coordinate with landscaping so that pits are accessible for cleaning.
9. Maintenance
- Clean roofs, gutters and filters before the monsoon.
- Check first-flush devices and remove silt from pits each year.
- Inspect tank covers, overflow pipes and mosquito screens.
- Replace filter media when it becomes clogged.
A neglected system quickly stops working. Simple annual maintenance keeps it effective for many years.
Frequently asked questions
Is rainwater harvesting mandatory in Jaipur?
Many urban local bodies require it for buildings above certain plot sizes. Check the conditions in your building plan approval and local byelaws.
Can rainwater be used for drinking?
Only with proper filtration, treatment and testing designed by experts. Most building systems use it for recharge or non-potable uses.
How often should recharge pits be cleaned?
At least once a year before the monsoon, with silt removed and filter media checked.
Where should a recharge pit be located?
Away from foundations, septic tanks and soak pits, at a point where roof water can reach it by gravity, as advised by the designer.
Sources
Planning a building or campus? Contact ATTPL Infra.